Cart
Checkout Secure

Coupon Code: FT68LD435 Copy Code

 

Got a Question? Call Us

800-906-2802

Mon-Sat 9am-6pm PST

Best Value Vacs 10L Solvent Pro Series Rotary Evaporator Turnkey Setup 10SPTS

sold in last hours
Your Price:
$19,205.00
10SPTS
Quantity
 
Checkout Secure
Quantity Remaining:
kind

85 of 100 Sold

Order in the next  to get it by 

Viewing This Product

 

4 Great reasons to buy from us:

  • Image of Secure Ordering
  • Image of 100% Satisfaction Guaranteed
  • Image of Easy Returns
  • Image of Free shipping (when you spend over XXX)

10L SOLVENT PRO SERIES ROTARY EVAPORATOR TURNKEY SETUP

10L Solvent Pro Series Rotary Evaporator turnkey setup includes all the necessary components to successfully perform solvent recovery via rotary evaporation. A cold trap should always be used inline between your vacuum system and application to protect the pump from volatile vapors. 

Rotovap Flow Chart

10L Rotary Evaporator Turnkey Setup includes:

  • 10L Solvent Pro Series Rotary Evaporator
  • Welch 2.3 cfm High Capacity 4 Head Oil-Free Diaphragm Pump 
  • Polyscience DuraChill -10C 1.5HP Chiller w/ Turbine Pump 
  • 20ft of Vacuum Tubing 
  • 20ft of Chiller Tubing 
  • 10 Pack of Adjustable Stainless Steel Hose Clamps
  • 3/8" Vacuum Manifold
  • Optional add-on: BVV CT40 -40°F 300ml x 3 Cold Trap, BVV CT80 -112°F 300ml x 3 Cold Trap 
  • Optional add-on: J-KEM DVR-200 Digital Vacuum Regulator 
  • Optional add-on: Heat Transfer Fluid -- NuTherm PF-50 or Dynalene HC-50

Rotovap Quick Start Guide

This guide gives basic quick start instructions for rotovaps. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs.

  • Clean and assemble unit. Make sure all pieces are cleaned and sterilized using an alcohol solution.
  • Connect chiller to condenser and set to 0C (32F). Always fill a rotovap condenser from the top down (chiller output to top of condenser, chiller input to bottom of condenser).
  • Connect vacuum pump to cold trap and connect cold trap to vacuum port on rotovap.
  • Turn on heat bath and set to 40C (113F).
  • Once heat bath, chiller and cold trap have reached desired temperatures, turn on rotovap motor and set speed to approximately 100 RPM (does not have to be precise). Keep in mind, higher RPM’s will increase evaporation power but also increase heat load.
  • Start vacuum pump and allow vacuum to pull down for a few minutes before injection.
  • Once vacuum has been pulled to a sufficient level (does not have to be precise but should be below 100 Torr), using the injection valve, very slowly inject approximately 500 mL of solution into evaporating flask and then close the valve. Allow this small amount to begin evaporating. You may see the chiller begin to rise in temperature, this is called “priming” the rotovap.
  • Once the temperature stops rising or all liquid is almost completely evaporated, open the injection valve again very slowly so that a small amount of liquid begins to enter the evaporating flask. Do not close injection valve this time but continue to allow solution to enter the evaporating flask. 
  • At this point you must try to match the input speed to the output speed. What this means is that you should be injecting the same amount of liquid into the rotovap that is equal to the amount of liquid dripping from the condenser into the receiving flask. You will know that the input speed and output speed are matched because the chiller will remain at a stable temperature. If the chiller begins to rise, then you are injecting too much liquid. Dial back the valve until the chiller stabilizes.
  • Once everything is stabilized, you may walk away from the rotovap if necessary. Check every so often to make sure temperatures remain stable and evaporation continues efficiently. 
  • SKU: 10SPTS
Shipping
 This Item Ships to 
Delivery

Estimated between  and

Will usually ship within 1 business day.

   

Please allow 10 days for your order to arrive. We source products from all over the world to bring you epic offers and the lowest prices. This means sometimes you have to wait a little longer to get your order but it's always worth it!

Returns are easy, simply contact us for a returns number and send your item to our returns centre for fast processing. We'll get you a replacement or refund in a snap!

Here are 4 more great reasons to buy from us:

   

Returns are easy, simply contact us for a returns number and send your item to our returns centre for fast processing. We'll get you a replacement or refund in a snap!

In the unlikely event that you find your item cheaper at another online store, just let us know and we'll beat the competitor's pricing hands-down.

We insist that you love everything you buy from us. If you're unhappy for any reason whatsoever, just let us know and we'll bend over backwards to make things right again.

Ordering from Kind Garden Supply is 100% safe and secure so you can rest easy. Your personal details are never shared, sold or rented to anyone either.

10L SOLVENT PRO SERIES ROTARY EVAPORATOR TURNKEY SETUP

10L Solvent Pro Series Rotary Evaporator turnkey setup includes all the necessary components to successfully perform solvent recovery via rotary evaporation. A cold trap should always be used inline between your vacuum system and application to protect the pump from volatile vapors. 

Rotovap Flow Chart

10L Rotary Evaporator Turnkey Setup includes:

  • 10L Solvent Pro Series Rotary Evaporator
  • Welch 2.3 cfm High Capacity 4 Head Oil-Free Diaphragm Pump 
  • Polyscience DuraChill -10C 1.5HP Chiller w/ Turbine Pump 
  • 20ft of Vacuum Tubing 
  • 20ft of Chiller Tubing 
  • 10 Pack of Adjustable Stainless Steel Hose Clamps
  • 3/8" Vacuum Manifold
  • Optional add-on: BVV CT40 -40°F 300ml x 3 Cold Trap, BVV CT80 -112°F 300ml x 3 Cold Trap 
  • Optional add-on: J-KEM DVR-200 Digital Vacuum Regulator 
  • Optional add-on: Heat Transfer Fluid -- NuTherm PF-50 or Dynalene HC-50

Rotovap Quick Start Guide

This guide gives basic quick start instructions for rotovaps. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs.

  • Clean and assemble unit. Make sure all pieces are cleaned and sterilized using an alcohol solution.
  • Connect chiller to condenser and set to 0C (32F). Always fill a rotovap condenser from the top down (chiller output to top of condenser, chiller input to bottom of condenser).
  • Connect vacuum pump to cold trap and connect cold trap to vacuum port on rotovap.
  • Turn on heat bath and set to 40C (113F).
  • Once heat bath, chiller and cold trap have reached desired temperatures, turn on rotovap motor and set speed to approximately 100 RPM (does not have to be precise). Keep in mind, higher RPM’s will increase evaporation power but also increase heat load.
  • Start vacuum pump and allow vacuum to pull down for a few minutes before injection.
  • Once vacuum has been pulled to a sufficient level (does not have to be precise but should be below 100 Torr), using the injection valve, very slowly inject approximately 500 mL of solution into evaporating flask and then close the valve. Allow this small amount to begin evaporating. You may see the chiller begin to rise in temperature, this is called “priming” the rotovap.
  • Once the temperature stops rising or all liquid is almost completely evaporated, open the injection valve again very slowly so that a small amount of liquid begins to enter the evaporating flask. Do not close injection valve this time but continue to allow solution to enter the evaporating flask. 
  • At this point you must try to match the input speed to the output speed. What this means is that you should be injecting the same amount of liquid into the rotovap that is equal to the amount of liquid dripping from the condenser into the receiving flask. You will know that the input speed and output speed are matched because the chiller will remain at a stable temperature. If the chiller begins to rise, then you are injecting too much liquid. Dial back the valve until the chiller stabilizes.
  • Once everything is stabilized, you may walk away from the rotovap if necessary. Check every so often to make sure temperatures remain stable and evaporation continues efficiently. 
  • SKU: 10SPTS
Shipping
This Item Ships to   
Delivery

Estimated between  and

Will usually ship within 1 business day.

   

Please allow 10 days for your order to arrive. We source products from all over the world to bring you epic offers and the lowest prices. This means sometimes you have to wait a little longer to get your order but it's always worth it!

Returns are easy, simply contact us for a returns number and send your item to our returns centre for fast processing. We'll get you a replacement or refund in a snap!

Here are 4 more great reasons to buy from us:

   

Returns are easy, simply contact us for a returns number and send your item to our returns centre for fast processing. We'll get you a replacement or refund in a snap!

In the unlikely event that you find your item cheaper at another online store, just let us know and we'll beat the competitor's pricing hands-down.

We insist that you love everything you buy from us. If you're unhappy for any reason whatsoever, just let us know and we'll bend over backwards to make things right again.

Ordering from Kind Garden Supply is 100% safe and secure so you can rest easy. Your personal details are never shared, sold or rented to anyone either.

Related Products

Best Value Vacs 10L Solvent Pro Series Rotary Evaporator Turnkey Setup 10SPTS

$19,205.00

Added to cart!

Get 5% Off

Your First Purchase Over $150


  • By clicking the button you'll
  • 1) confirm you're a genius
  • 2) be kept in the loop about the latest gear and deals.
🚛🚚📦Spend $x to Unlock Free Shipping Free shipping when you order over XX You Have Qualified for Free Shipping 📦 💚📦Spend $x to Unlock Free Shipping 🚛🚚🚛🚚 You Have Achieved Free Shipping Free Shipping For Over $x to Free Shipping Over $x to You Have Achieved Free Shipping Free shipping when you order over XX ou Have Qualified for Free Shipping